Scott Hull on Vinyl, Part Four

Header image for Scott Hull on Vinyl series

One of the most sought after vinyl-cutting systems in the world is the nearly indestructible VMS-70 and VMS-80 cutting systems built by Neumann. The VMS-82 was the last of these produced. I’m thankful to say that we get to use our VMS-82 lathe every day to cut lacquers for clients around the globe. (Fig. 1)

Photo of the Masterdisk lathe
Fig. 1
The actual cutting happens at the cutter head. In this case, the BMW of cutter heads, the SX-74. (Fig. 2)

Though it was initially built in 1974, this design was never dramatically improved. It was capable of cutting with sufficient level and flat frequency response to please nearly everyone.

The head has been removed from the lathe and is sitting upside down for viewing. (Fig. 3)

Now just a little closer look to see the working parts of this little marvel.

Photo of Neumann SX 74 name plate
Fig. 2
The two round “cans” on either side are the voice coils. (Fig. 4) You can also see the cutting stylus: a faceted sapphire glued to a pin that mounts in the tube that connects to each voice coil. Also in the foreground are two fine wires. These carry a small voltage that heats the stylus to an optimal temperature so that it slices smoothly through the lacquer instead of dragging and causing extra noise from a jagged cut.

The drive coils of the stereo cutter head are mounted at right angles. When there is audio in the left channel the left coil goes in and out, just like a speaker does. And when there is audio in the right channel the right coil goes in and out. One voice coil in the cutter head is wired deliberately out of phase so that when a mono signal is cut, as the left coil is moving in the right coil is moving out. Thus, a mono signal cuts a lateral groove that looks like this. (Fig. 5)

Why is this done this way you might ask?

Photo of the Neumann lathe cutter head
Fig. 3
We have go back to mono to find out. Early records, initially 78s and then LPs, were mono. Systems that cut mono records had only one drive coil and it moved the cutting stylus back and forth creating a lateral, constant-depth groove. There was little concern about the depth of the cut so long as it was deep enough to hold the playback stylus in the groove. Then along came stereo. Researchers needed to find a way to carve two channels of audio into a record but make the new technology compatible with mono records and players.

Unfortunately, today’s technology designers don’t put quite so much effort into forward- and backward-compatibility. That’s a soapbox speech for another time.

So what they came up with was to record the mono component of the stereo audio laterally, like on a mono record. Then by adding a second coil and wiring it “out of phase” with the first coil they created depth modulation which records the stereo or side signal.

If I’ve lost you, take a breath and read on; I’ll try to make it clearer.

Photo of Neumann cutter head close up
Fig. 4
Stereo is made up of a left signal and a right signal. OK, that’s simple. But stereo can also be described as the mono component (everything that is exactly the same in both speakers) and the difference component (everything that is different). This is commonly called Middle and Side, or M-S for short. A stereo signal can be converted into an M-S signal and back again with nearly no change at all. FM radio is transmitted in M-S. The middle signal is a strong “full wave” signal and it is this signal that you hear when you are far away from the radio tower. That signal is mono. As you get closer to the radio tower, your radio can tune in the sub carrier signal, which carries the difference (side channel). When you receive a strong enough signal, the FM station now plays back in full stereo because it has BOTH the middle and the side signals. It can be hard to believe, because we commonly think in left-and-right rather than middle-and-side. But it’s true. It’s a matter of physics and alternating current electronics. Are you still with me?

Photo of record groove
Fig. 5
The groove shows us the “difference” signal by it’s depth. So a mastering engineer speaks “lateral” and means the mono aka “middle” signal. And when the engineer says “vertical” he or she is referring to the “difference” aka “side” signals. Got it now? Good.

Once you have a hold of that concept then we can start to talk about why some records seem to make the vocals spitty and sibilant. And why some recordings have to be modified with equalization to minimize out-of-phase bass.

But there is one more thing to understand before we can control our quality. It was a standard developed in the 1950s called the RIAA Curve.

Next week I’ll talk about what the RIAA curve is, why it was standardized, and what steps we have to take to make records sound really good.

(Read all of the “Scott Hull on Vinyl” articles here.)

Fill out my online form.